Torcia ArmyTek Predator R5 vers. 2012 Silver OP

NUOVA VERSIONE

MODELLO 2012

Versione Silver OP

Caratteristiche:

Led seconda generazione R5

Lumens: Fino a 500
Durata batteria 1x 18650 ore 1.25 alla massima potenza
Distanza throw: oltre 200 metri
Regolazione della luce tramite twist della testa
Memoria sull' ultima regolazione
Momentary On

FORNITO DI:

Clip di aggancio stessa colorazione della testa

O ring di ricambio

Laccetto

Tastino in gomma di ricambio

COMPARATIVA LED S2  VS  R5 da Fonarevka

INFORMAZIONI DAL SITO DEL PRODUTTORE:

Review by selfbuilt. English version.
Review by light-reviews.com. English version.
Review by mefistofele86. English version.
Review by mefistofele86. Italian version.
Review by awl. Russian version.
Review by AVM. Russian version.
Review by Pikom. Polish version.
Review by mar3. Polish version.
Review by ichoderso. German version.
Review by gunga. English version.

LED Cree XP-G (USA) is driven by 1.5A (R5 with 1C tint)
- Uses 2nd generation of LED drivers
- 3 types of current stabilization are selectable by user: full stabilization (FULL), simple semi-stabilization as for the buck driver (SEMI) and stepped stabilization (STEP).
- The real long duration and the flat runtimes with FULL stabilization for one 18650 Li-Ion battery at each mode against the standard buck drivers.
- The specially calculated long-range reflector intended for LED Cree XP-G (light beam with the angle of 5 degrees for the distances of 200 meters).
- The changeable quantity of modes and maximal tuning of them.
- The voltage supply selection, which allows using the batteries without protection board (PCB).
- Maximal mode without thermal runtime limits.
- The Firefly mode 0.1 lumens with runtime up to 100 days.
and etc.

The full features and manual you can download there: http://www.armytek.com/content/predator_manual.pdf

This flashlight is designed with the specially calculated long-range reflector intended for LED Cree XP-G. Fine alignment of light beam with the angle of 5 degrees as well as the faultless beam for the distances up to 250 meters (820 feet). The spot diameter is 8 meters for 100 meters of beam distance. The full spill is 24 degrees.

S-Tek™, the next generation advanced electronics circuitry is based on the ECO algorithms which decrease the system power consumption and make this flashlight highly effective through the full battery usage.

The recent LED Cree XP-G (USA) is supplied by maximum current of 1.5 amp. The LED is not overheated and the luminous flux drop is minimal owing to the highly efficient heat removal and an advanced electronic circuitry.

Adjustable quantity of modes with full tuning capabilities and continuously-variable selection.

The real-world high efficiency, long duration and flat runtimes with FULL stabilization for one 18650 Li-Ion battery for each mode (in contrast to the standard buck circuitry).

The current stabilization diagrams are entirely changeable through the user menu: full stabilization (FULL), simple semistabilization as for the buck driver (SEMI) and stepped stabilization (STEP).

The voltage supply selection allows using the batteries without protection board (PCB), for example: LiFePO4.

Maximal output mode without thermal runtime limits.

This flashlight is designed with the temperature sensor inside to prevent the LED overheating in extreme environments.

Availability of the Firefly mode 0.1 lumens with runtime up to 100 days (in contrast to standard 120 hours for low output mode).

The O-rings and threads are greased by Nyogel 760G.

Constant brightness without flicker effects.

Low voltage and high temperature indication.

Selectable automatic memorization of last chosen mode.

Resettable factory defaults (Military or Outdoor).

Advanced electronic protection from incorrect battery installation.

The flashlight is designed with the impact-resistant bezels from both sides in order to protect it from falling and allow utilization during combat situations.

The bezels are made of solid stainless steel covered with special gold-colored Titanium coating, which is 10 times harder than Type III hard anodization. There is also a flashlight modification with matt stainless steel bezels.

The built-in removable clip, convenient and durable.

Ergonomic design and reliable build quality for easy handling.

The rigid indestructible body, which does not roll and is protected from impacts and scratches. The body is developed for the lower weight with sufficient durability.

The metric threads for better water resistance made precisely for long life usage.

The flashlight has double silicone O-rings for each body thread and additional O-rings for tailcap and L-shaped ring under the glass for improved water resistance.

The flashlight possesses the ultra transparent hardened glass with anti-reflective coating, which is used in photo lenses.

The tough and easy-to-remove lanyard to avoid losing the flashlight and for comfortable access.

Protection from accidental switch-on (special turn of the tailcap).

Advanced quality control.

The hard, scratch and impact-resistant matt anodizing coating with hardness HV400.

Made of aircraft-grade aluminum T6061-T6.

Water resistance to IPX-8 standard.

Uses 2xCR123A batteries or rechargeable 1x18650 Li-Ion / 2xR123 Li-Ion batteries or rechargeable 1xLiFePO4 batteries.

Approx. dimensions: L 6.1" x D 1.43" (L 155 x D 36.5mm), body D 1" (D 25.4mm), weight: 4.23oz (120g)

Included accessories: holster, lanyard, O-rings, rubber button

info@lamelancette.com